emc2301-openwrt.patch

diff --git a/target/linux/bcm27xx/bcm2711/config-5.10 b/target/linux/bcm27xx/bcm2711/config-5.10
index 03d84378b3..c6a08891e5 100644
--- a/target/linux/bcm27xx/bcm2711/config-5.10
+++ b/target/linux/bcm27xx/bcm2711/config-5.10
@@ -57,7 +57,7 @@ CONFIG_BCM2835_DEVGPIOMEM=y
 CONFIG_BCM2835_MBOX=y
 CONFIG_BCM2835_POWER=y
 # CONFIG_BCM2835_SMI is not set
-# CONFIG_BCM2835_THERMAL is not set
+CONFIG_BCM2835_THERMAL=y
 CONFIG_BCM2835_VCHIQ=y
 # CONFIG_BCM2835_VCHIQ_MMAL is not set
 CONFIG_BCM2835_WDT=y
@@ -239,14 +239,28 @@ CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT_MAP=y
 CONFIG_HOLES_IN_ZONE=y
 CONFIG_HOTPLUG_CPU=y
+CONFIG_HWMON=y
 CONFIG_HW_CONSOLE=y
 CONFIG_HW_RANDOM=y
 # CONFIG_HW_RANDOM_BCM2835 is not set
 CONFIG_HW_RANDOM_IPROC_RNG200=y
 CONFIG_I2C=y
-# CONFIG_I2C_BCM2708 is not set
+CONFIG_I2C_ALGOBIT=y
+CONFIG_I2C_BCM2708=y
+CONFIG_I2C_BCM2708_BAUDRATE=100000
+CONFIG_I2C_BCM2835=y
 CONFIG_I2C_BOARDINFO=y
-# CONFIG_I2C_BRCMSTB is not set
+CONFIG_I2C_BRCMSTB=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_COMPAT=y
+CONFIG_I2C_GPIO=y
+CONFIG_I2C_HELPER_AUTO=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_GPMUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_I2C_MUX_PINCTRL=y
+CONFIG_I2C_ROBOTFUZZ_OSIF=y
+CONFIG_I2C_TINY_USB=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000
@@ -302,6 +316,7 @@ CONFIG_MMC_SDHCI_IPROC=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MODULES_USE_ELF_RELA=y
 # CONFIG_MTD is not set
+CONFIG_MULTIPLEXER=y
 CONFIG_MUTEX_SPIN_ON_OWNER=y
 CONFIG_NEED_DMA_MAP_STATE=y
 CONFIG_NEED_SG_DMA_LENGTH=y
@@ -354,6 +369,7 @@ CONFIG_PM_SLEEP=y
 CONFIG_PM_SLEEP_SMP=y
 CONFIG_POWER_RESET=y
 CONFIG_POWER_SUPPLY=y
+CONFIG_POWER_SUPPLY_HWMON=y
 CONFIG_PRINTK_TIME=y
 CONFIG_QUEUED_RWLOCKS=y
 CONFIG_QUEUED_SPINLOCKS=y
@@ -381,6 +397,9 @@ CONFIG_RWSEM_SPIN_ON_OWNER=y
 CONFIG_SCSI=y
 # CONFIG_SCSI_LOWLEVEL is not set
 # CONFIG_SCSI_PROC_FS is not set
+CONFIG_SENSORS_EMC2301=y
+CONFIG_SENSORS_RASPBERRYPI_HWMON=y
+# CONFIG_SENSORS_RPI_POE_FAN is not set
 CONFIG_SERIAL_8250_BCM2835AUX=y
 # CONFIG_SERIAL_8250_DMA is not set
 CONFIG_SERIAL_8250_EXTENDED=y
@@ -417,6 +436,7 @@ CONFIG_THERMAL=y
 CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
 CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
 CONFIG_THERMAL_GOV_STEP_WISE=y
+CONFIG_THERMAL_HWMON=y
 CONFIG_THERMAL_OF=y
 CONFIG_THERMAL_WRITABLE_TRIPS=y
 CONFIG_THREAD_INFO_IN_TASK=y
diff --git a/target/linux/bcm27xx/patches-5.10/999-0000-Add-emc2301-cm4io-fan-support.patch b/target/linux/bcm27xx/patches-5.10/999-0000-Add-emc2301-cm4io-fan-support.patch
new file mode 100644
index 0000000000..8acd725d8a
--- /dev/null
+++ b/target/linux/bcm27xx/patches-5.10/999-0000-Add-emc2301-cm4io-fan-support.patch
@@ -0,0 +1,630 @@
+From 28159fb33035dd138fed590c920bb7d29facfabc Mon Sep 17 00:00:00 2001
+From: shayne <me@example.com>
+Date: Wed, 29 Jun 2022 17:33:39 -0400
+Subject: [PATCH] Add emc2301 cm4io-fan support
+
+---
+ arch/arm/boot/dts/overlays/Makefile           |   1 +
+ .../boot/dts/overlays/cm4io-fan-overlay.dts   |  72 +++
+ drivers/hwmon/Kconfig                         |  10 +
+ drivers/hwmon/Makefile                        |   1 +
+ drivers/hwmon/emc2301.c                       | 483 ++++++++++++++++++
+ 5 files changed, 567 insertions(+)
+ create mode 100644 arch/arm/boot/dts/overlays/cm4io-fan-overlay.dts
+ create mode 100644 drivers/hwmon/emc2301.c
+
+diff --git a/arch/arm/boot/dts/overlays/Makefile b/arch/arm/boot/dts/overlays/Makefile
+index fbcc3e35a..3921296fd 100644
+--- a/arch/arm/boot/dts/overlays/Makefile
++++ b/arch/arm/boot/dts/overlays/Makefile
+@@ -33,6 +33,7 @@ dtbo-$(CONFIG_ARCH_BCM2835) += \
+ 	cap1106.dtbo \
+ 	chipdip-dac.dtbo \
+ 	cma.dtbo \
++	cm4io-fan.dtbo \
+ 	dht11.dtbo \
+ 	dionaudio-loco.dtbo \
+ 	dionaudio-loco-v2.dtbo \
+diff --git a/arch/arm/boot/dts/overlays/cm4io-fan-overlay.dts b/arch/arm/boot/dts/overlays/cm4io-fan-overlay.dts
+new file mode 100644
+index 000000000..901fd332b
+--- /dev/null
++++ b/arch/arm/boot/dts/overlays/cm4io-fan-overlay.dts
+@@ -0,0 +1,72 @@
++/*
++ * Overlay for EMC2301 fan control chip on the Raspberry Pi Compute Module 4 IO board.
++ */
++#include <dt-bindings/thermal/thermal.h>
++
++/dts-v1/;
++/plugin/;
++
++/ {
++    compatible = "brcm,bcm2835";
++
++    fragment@0 {
++        target = <&i2c_csi_dsi>;
++        __overlay__ {
++            status = "okay";
++        };
++    };
++
++    fragment@1 {
++        target = <&i2c_csi_dsi>;
++        __overlay__ {
++            fanctrl: emc2301@2f {
++                reg = <0x2f>;
++                compatible = "microchip,emc2301";
++                #cooling-cells = <0x02>;
++
++                fan0: fan@0 {
++                    min-rpm = /bits/ 16 <3500>;
++                    max-rpm = /bits/ 16 <5500>;
++                };
++            };
++        };
++    };
++
++    fragment@2 {
++        target = <&cpu_thermal>;
++        polling-delay = <2000>; /* milliseconds */
++        __overlay__ {
++            trips {
++                fanmid0: fanmid0 {
++                    temperature = <50000>;
++                    hysteresis = <2000>;
++                    type = "active";
++                };
++                fanmax0: fanmax0 {
++                    temperature = <75000>;
++                    hysteresis = <2000>;
++                    type = "active";
++                };
++            };
++            cooling-maps {
++                map0 {
++                    trip = <&fanmid0>;
++                    cooling-device = <&fanctrl 2 6>;
++                };
++                map1 {
++                    trip = <&fanmax0>;
++                    cooling-device = <&fanctrl 7 THERMAL_NO_LIMIT>;
++                };
++            };
++        };
++    };
++
++    __overrides__ {
++        midtemp =	<&fanmid0>,"temperature:0";
++        midtemp_hyst =	<&fanmid0>,"hysteresis:0";
++        maxtemp =	<&fanmax0>,"temperature:0";
++        maxtemp_hyst =	<&fanmax0>,"hysteresis:0";
++        minrpm =	<&fan0>,"min-rpm;0";
++        maxrpm =	<&fan0>,"max-rpm;0";
++    };
++};
+diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
+index a14a97785..513f30a0a 100644
+--- a/drivers/hwmon/Kconfig
++++ b/drivers/hwmon/Kconfig
+@@ -1612,6 +1612,16 @@ config SENSORS_EMC2103
+ 	  This driver can also be built as a module. If so, the module
+ 	  will be called emc2103.
+ 
++config SENSORS_EMC2301
++	tristate "SMSC EMC2301"
++	depends on I2C
++	help
++	  If you say yes here you get support for the temperature
++	  and fan sensors of the SMSC EMC2301 chips.
++
++	  This driver can also be built as a module. If so, the module
++	  will be called emc2301.
++
+ config SENSORS_EMC6W201
+ 	tristate "SMSC EMC6W201"
+ 	depends on I2C
+diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
+index dc68c9788..ca2ffe8e5 100644
+--- a/drivers/hwmon/Makefile
++++ b/drivers/hwmon/Makefile
+@@ -66,6 +66,7 @@ obj-$(CONFIG_SENSORS_DS620)	+= ds620.o
+ obj-$(CONFIG_SENSORS_DS1621)	+= ds1621.o
+ obj-$(CONFIG_SENSORS_EMC1403)	+= emc1403.o
+ obj-$(CONFIG_SENSORS_EMC2103)	+= emc2103.o
++obj-$(CONFIG_SENSORS_EMC2301)	+= emc2301.o
+ obj-$(CONFIG_SENSORS_EMC6W201)	+= emc6w201.o
+ obj-$(CONFIG_SENSORS_F71805F)	+= f71805f.o
+ obj-$(CONFIG_SENSORS_F71882FG)	+= f71882fg.o
+diff --git a/drivers/hwmon/emc2301.c b/drivers/hwmon/emc2301.c
+new file mode 100644
+index 000000000..250651d8f
+--- /dev/null
++++ b/drivers/hwmon/emc2301.c
+@@ -0,0 +1,483 @@
++/*
++ * Driver for the Microchip/SMSC EMC2301 Fan controller
++ *
++ * Copyright (C) 2018-2020 Traverse Technologies
++ * Author: Mathew McBride <matt@traverse.com.au>
++ *
++ * Based in part on an earlier implementation by
++ * Reinhard Pfau <pfau@gdsys.de>
++ *
++ * SPDX-License-Identifier: GPL-2.0
++ *
++ */
++
++#include <linux/err.h>
++#include <linux/hwmon.h>
++#include <linux/hwmon-sysfs.h>
++#include <linux/i2c.h>
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/version.h>
++#include <linux/thermal.h>
++
++#if LINUX_VERSION_CODE <= KERNEL_VERSION(5, 2, 0)
++#define HWMON_CHANNEL_INFO(stype, ...) \
++	(&(struct hwmon_channel_info){ .type = hwmon_##stype, .config = (u32[]){ __VA_ARGS__, 0 } })
++#endif
++/*
++ * Factor by equations [2] and [3] from data sheet; valid for fans where the
++ * number of edges equals (poles * 2 + 1).
++ */
++#define FAN_RPM_FACTOR 3932160
++#define FAN_TACH_MULTIPLIER 1
++
++#define TACH_HIGH_MASK GENMASK(12, 5)
++#define TACH_LOW_MASK GENMASK(4, 0)
++
++#define EMC230X_REG_PRODUCT_ID 0xFD
++
++#define EMC230X_REG_MINTACH 0x38
++
++#define EMC230X_MAX_COOLING_STATE 7
++
++static bool register_cdev = 1;
++module_param(register_cdev, bool, 0);
++MODULE_PARM_DESC(register_cdev, "Set to zero to disable registering a cooling device");
++
++struct emc2301_data {
++	struct device *dev;
++	struct i2c_client *i2c;
++	u8 num_fans;
++	u16 minimum_rpm[5];
++	struct thermal_cooling_device *cdev;
++
++	u8 current_cooling_state;
++	u16 cooling_step[5];
++	u16 min_rpm[5];
++	u16 max_rpm[5];
++	u16 setpoint[5];
++};
++
++static u16 emc2301_read_fan_tach_int(struct emc2301_data *data, int channel)
++{
++	struct i2c_client *i2c = data->i2c;
++
++	u8 channel_reg;
++	u8 channel_high, channel_low;
++	u16 channel_combined;
++
++	channel_reg = 0x3e + (channel * 0x02);
++#if 0
++	dev_dbg(data->dev, "Reading channel %d register %X\n", channel, channel_reg);
++#endif
++
++	channel_high = i2c_smbus_read_byte_data(i2c, channel_reg);
++
++	channel_low = i2c_smbus_read_byte_data(i2c, channel_reg + 0x01);
++	channel_combined = ((u16)channel_high << 5) | (channel_low >> 3);
++
++#if 0
++	dev_dbg(data->dev, "Got values %04X for channel %d\n", channel_combined, channel);
++#endif
++
++	return channel_combined;
++}
++
++static u16 emc2301_read_fan_tach(struct device *dev, int channel)
++{
++	struct emc2301_data *data = dev_get_drvdata(dev);
++	return emc2301_read_fan_tach_int(data, channel);
++}
++
++static int emc2301_read_fan_rpm(struct device *dev, int channel, long *val)
++{
++	u16 channel_tach;
++	u16 fan_rpm;
++
++	channel_tach = emc2301_read_fan_tach(dev, channel);
++
++	fan_rpm = (FAN_RPM_FACTOR * FAN_TACH_MULTIPLIER) / channel_tach;
++	*val = fan_rpm;
++
++	return 0;
++}
++
++/* Write a target RPM to the TACH target register
++ * This requires RPM speed control to be enabled with
++ * EN_ALGO in the fan configuration register.
++ */
++static int emc2301_set_fan_rpm(struct emc2301_data *devdata, int channel, long target_rpm)
++{
++	long rpm_high, rpm_low;
++	long target_tach;
++	u8 channel_reg;
++
++	channel_reg = 0x3c + (channel * 10);
++
++	target_tach = (FAN_RPM_FACTOR * FAN_TACH_MULTIPLIER) / target_rpm;
++	dev_dbg(devdata->dev, "RPM %ld requested, target tach is %ld\n", target_rpm, target_tach);
++
++	rpm_high = (target_tach & TACH_HIGH_MASK) >> 5;
++	rpm_low = (target_tach & TACH_LOW_MASK);
++
++#if 0
++	dev_dbg(devdata->dev, "Writing %02lX %02lX to %02X+%02X\n", rpm_low, rpm_high,
++		channel_reg, channel_reg+1);
++#endif
++
++	i2c_smbus_write_byte_data(devdata->i2c, channel_reg, rpm_low);
++	i2c_smbus_write_byte_data(devdata->i2c, channel_reg + 1, rpm_high);
++
++	devdata->setpoint[channel] = (u16)target_rpm;
++
++	return 0;
++}
++
++static int emc2301_fan_get_max_state(struct thermal_cooling_device *cdev, unsigned long *state)
++{
++	*state = EMC230X_MAX_COOLING_STATE;
++	return 0;
++}
++
++static int emc2301_fan_get_cur_state(struct thermal_cooling_device *cdev, unsigned long *state)
++{
++	struct emc2301_data *devdata = cdev->devdata;
++	*state = devdata->current_cooling_state;
++
++	return 0;
++}
++
++static int emc2301_fan_set_cur_state(struct thermal_cooling_device *cdev, unsigned long state)
++{
++	struct emc2301_data *devdata = cdev->devdata;
++	struct device *dev = devdata->dev;
++
++	u16 rpm = 0;
++	int i = 0;
++	int retval = 0;
++
++	dev_dbg(dev, "emc2301_fan_set_cur_state %ld\n", state);
++
++	if (devdata->i2c == NULL) {
++		dev_err(dev, "ERROR: no i2c instance\n");
++		return -EINVAL;
++	}
++
++	if (state < 0 || state > EMC230X_MAX_COOLING_STATE)
++		return -EINVAL;
++
++	for (i = 0; i < ARRAY_SIZE(devdata->cooling_step); i++) {
++		if (devdata->cooling_step[i] > 0) {
++			rpm = devdata->min_rpm[i] + ((state + 1) * devdata->cooling_step[i]);
++			devdata->current_cooling_state = state;
++			if (emc2301_set_fan_rpm(devdata, i, rpm)) {
++				retval = 1;
++			}
++		}
++	}
++
++	return retval;
++}
++
++struct thermal_cooling_device_ops emc2301_thermal_cooling_device = {
++	.get_max_state = emc2301_fan_get_max_state,
++	.get_cur_state = emc2301_fan_get_cur_state,
++	.set_cur_state = emc2301_fan_set_cur_state,
++};
++
++static int emc2301_read_fan_fault(struct device *dev, struct i2c_client *i2c, int channel, long *val)
++{
++	u8 status_reg;
++
++	if (channel > 1) {
++		return -EOPNOTSUPP;
++	}
++	status_reg = i2c_smbus_read_byte_data(i2c, 0x24);
++	dev_dbg(dev, "Channel %d status register %02X\n", channel, status_reg);
++
++	if (status_reg & 0x7) {
++		*val = 1;
++	} else {
++		*val = 0;
++	}
++
++	return 0;
++}
++
++static int emc2301_read_fan_target(struct emc2301_data *devdata, int channel, long *val)
++{
++	if (channel > devdata->num_fans) {
++		return -EINVAL;
++	}
++	*val = devdata->setpoint[channel];
++	return 0;
++}
++
++static int emc2301_read(struct device *dev, enum hwmon_sensor_types type, u32 attr, int channel, long *val)
++{
++	struct emc2301_data *data = dev_get_drvdata(dev);
++	struct i2c_client *i2c = data->i2c;
++
++	if (type != hwmon_fan) {
++		return -EOPNOTSUPP;
++	}
++	if (channel > data->num_fans) {
++		return -ENOTSUPP;
++	}
++	switch (attr) {
++	case hwmon_fan_input:
++		return emc2301_read_fan_rpm(dev, channel, val);
++	case hwmon_fan_target:
++		return emc2301_read_fan_target(data, channel, val);
++	case hwmon_fan_fault:
++		return emc2301_read_fan_fault(dev, i2c, channel, val);
++	default:
++		return -ENOTSUPP;
++		break;
++	}
++
++	return 0;
++}
++
++static int emc2301_write(struct device *dev, enum hwmon_sensor_types type, u32 attr, int channel, long val)
++{
++	struct emc2301_data *data = dev_get_drvdata(dev);
++
++	if (channel > data->num_fans)
++		return -EINVAL;
++
++	switch (type) {
++	case hwmon_fan:
++		switch (attr) {
++		case hwmon_fan_target:
++#if 0
++			if (val < data->minimum_rpm[channel]) {
++				dev_err(dev, "RPM %ld is lower than channel minimum %ld\n", val, data->minimum_rpm[channel]);
++				return -EINVAL;
++			}
++#endif
++
++			dev_dbg(dev, "emc2301_write hwmon_fan_target %ld\n", val);
++			return emc2301_set_fan_rpm(data, channel, val);
++		default:
++			return -EOPNOTSUPP;
++		}
++	default:
++		return -EOPNOTSUPP;
++		break;
++	}
++	return -EOPNOTSUPP;
++}
++
++static const struct hwmon_channel_info *emc2301_info[] = {
++	HWMON_CHANNEL_INFO(fan, HWMON_F_INPUT | HWMON_F_FAULT | HWMON_F_TARGET), NULL
++};
++
++static umode_t emc2301_is_visible(const void *drvdata, enum hwmon_sensor_types type, u32 attr, int channel)
++{
++	//const struct emc2301_data *data = drvdata;
++
++	switch (type) {
++	case hwmon_fan:
++		switch (attr) {
++		case hwmon_fan_input:
++		case hwmon_fan_fault:
++			return S_IRUGO;
++		case hwmon_fan_target:
++			return S_IRUGO | S_IWUSR;
++		default:
++			break;
++		}
++		break;
++	default:
++		break;
++	}
++	return 0;
++}
++
++static const struct hwmon_ops emc2301_ops = {
++	.is_visible = emc2301_is_visible,
++	.read = emc2301_read,
++	.write = emc2301_write,
++};
++
++static const struct hwmon_chip_info emc2301_chip_info = {
++	.ops = &emc2301_ops,
++	.info = emc2301_info,
++};
++
++static int emc2301_enable_rpm_control(struct emc2301_data *data, u16 fan_dev, bool enable)
++{
++	u8 fan_config_reg_addr;
++	u8 fan_config_reg_val;
++	int ret = 0;
++
++	// get current fan config reg value
++	fan_config_reg_addr = 0x32 + (fan_dev * 0x10);
++	fan_config_reg_val = i2c_smbus_read_byte_data(data->i2c, fan_config_reg_addr);
++
++	// update config reg to enable/disable control as requested
++	if (enable) {
++		// set ENAx to enable drive
++		fan_config_reg_val |= (1 << 7);
++		// clear RNGx to set minRPM=500
++		fan_config_reg_val &= ~(0b11 << 5);
++	} else {
++		// clear ENAx
++		fan_config_reg_val &= ~(1 << 7);
++	}
++
++	dev_dbg(data->dev, "Writing 0x%02X to 0x%02X\n", fan_config_reg_val, fan_config_reg_addr);
++
++	ret = i2c_smbus_write_byte_data(data->i2c, fan_config_reg_addr, fan_config_reg_val);
++	if (ret) {
++		dev_err(data->dev, "Unable to write fan configuration register %02X\n", fan_config_reg_addr);
++		return ret;
++	}
++
++	if (!enable) {
++		ret = i2c_smbus_write_byte_data(data->i2c, (0x30 + (fan_dev * 0x10)), 0xFF);
++	}
++	return ret;
++};
++
++static int emc2301_i2c_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
++{
++	struct device *hwmon_dev;
++	struct device_node *of_node = i2c->dev.of_node;
++	struct device_node *child_node;
++	struct emc2301_data *data;
++	int8_t regval;
++	u8 i, retval;
++	u16 chan_val;
++	u16 range;
++	bool has_cooling_step = false;
++	int numchildren = 0;
++
++	if (!i2c_check_functionality(i2c->adapter, I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA))
++		return -ENODEV;
++
++	data = devm_kzalloc(&i2c->dev, sizeof(struct emc2301_data), GFP_KERNEL);
++	if (unlikely(!data))
++		return -ENODEV;
++
++	data->dev = &i2c->dev;
++	data->i2c = i2c;
++
++	regval = i2c_smbus_read_byte_data(i2c, EMC230X_REG_PRODUCT_ID);
++	switch (regval) {
++	case 0x34: /* EMC2305 */
++		data->num_fans = 5;
++		break;
++	case 0x35: /* EMC2303 */
++		data->num_fans = 3;
++		break;
++	case 0x36: /* EMC2302 */
++		data->num_fans = 2;
++		break;
++	case 0x37: /* EMC2301 */
++		data->num_fans = 1;
++		break;
++	default:
++		dev_err(&i2c->dev, "Unknown product ID %d\n", regval);
++		return -ENODEV;
++	}
++	dev_info(&i2c->dev, "EMC230%d detected\n", data->num_fans);
++
++	memset(data->min_rpm, 0, sizeof(u16) * ARRAY_SIZE(data->min_rpm));
++	memset(data->max_rpm, 0, sizeof(u16) * ARRAY_SIZE(data->max_rpm));
++
++	/* Read minimum and maximum RPM values from device
++	 * tree, if specified.
++	 * For example, the Noctua NF-A4x20 has a min
++	 * RPM of 1200 and a max of 5000-5500.
++	 * Without this, cooling actions with slower
++	 * fans may not be effective
++	 */
++	if (of_node) {
++		numchildren = of_get_child_count(of_node);
++		dev_info(&i2c->dev, "Have %d fans configured in DT\n", numchildren);
++		if (numchildren > data->num_fans) {
++			dev_warn(&i2c->dev,
++				 "%d fans are specified in DT, but only %d fans are supported by this device",
++				 numchildren, data->num_fans);
++			numchildren = data->num_fans;
++		}
++		child_node = of_node->child;
++
++		for (i = 0; i < numchildren; i++) {
++			retval = of_property_read_u16(child_node, "min-rpm", &chan_val);
++			if (!retval) {
++				data->min_rpm[i] = chan_val;
++			}
++
++			retval = of_property_read_u16(child_node, "max-rpm", &chan_val);
++			if (!retval) {
++				data->max_rpm[i] = chan_val;
++			}
++			child_node = of_get_next_child(of_node, child_node);
++		}
++	} else {
++		dev_warn(&i2c->dev, "No device tree node found for this device");
++	}
++
++	for (i = 0; i < data->num_fans; i++) {
++		if (data->min_rpm[i] != 0 && data->max_rpm[i] != 0) {
++			range = data->max_rpm[i] - data->min_rpm[i];
++			data->cooling_step[i] = range / (EMC230X_MAX_COOLING_STATE + 1);
++			dev_info(&i2c->dev, "Fan %i Cooling step is %d RPM, minimum %d, max %d RPM\n", i,
++				 data->cooling_step[i], data->min_rpm[i], data->max_rpm[i]);
++			has_cooling_step = true;
++			emc2301_enable_rpm_control(data, i, true);
++			emc2301_set_fan_rpm(data, i, data->max_rpm[i]);
++		} else {
++			data->cooling_step[i] = 0;
++		}
++	}
++
++	data->current_cooling_state = EMC230X_MAX_COOLING_STATE;
++
++#if 0
++	/* Read the fan minimum tach values */
++	for(i=0; i<data->num_fans; i++) {
++		channel_reg = EMC230X_REG_MINTACH + (i * 10);
++		regval = i2c_smbus_read_byte_data(i2c, channel_reg);
++		min_tach = (FAN_RPM_FACTOR * FAN_TACH_MULTIPLIER) / (regval << 5);
++		data->minimum_rpm[i] = (FAN_RPM_FACTOR * FAN_TACH_MULTIPLIER) / min_tach;
++		dev_info(&i2c->dev, "Channel %d minimum RPM is %d", i, data->minimum_rpm[i]);
++	}
++#endif
++	hwmon_dev =
++		devm_hwmon_device_register_with_info(&i2c->dev, i2c->name, data, &emc2301_chip_info, NULL);
++
++	if (IS_REACHABLE(CONFIG_THERMAL) && has_cooling_step && register_cdev == 1) {
++		dev_info(&i2c->dev, "registering a cooling device");
++		data->cdev = devm_thermal_of_cooling_device_register(&i2c->dev, of_node, "emc2301_fan", data,
++								     &emc2301_thermal_cooling_device);
++		if (IS_ERR(data->cdev)) {
++			dev_err(&i2c->dev, "Failed to register cooling device\n");
++			return PTR_ERR(data->cdev);
++		}
++	}
++
++	return PTR_ERR_OR_ZERO(hwmon_dev);
++}
++
++static const struct i2c_device_id emc2301_i2c_id[] = { { "emc2305", 0 }, { "emc2304", 0 }, { "emc2303", 0 },
++						       { "emc2302", 0 }, { "emc2301", 0 }, {} };
++
++MODULE_DEVICE_TABLE(i2c, emc2301_i2c_id);
++
++static struct i2c_driver emc2301_i2c_driver = {
++	.driver = {
++		.name = "emc2301",
++	},
++	.probe    = emc2301_i2c_probe,
++	.id_table = emc2301_i2c_id,
++};
++
++module_i2c_driver(emc2301_i2c_driver);
++
++MODULE_DESCRIPTION("EMC2301 Fan controller driver");
++MODULE_AUTHOR("Mathew McBride <matt@traverse.com.au>");
++MODULE_LICENSE("GPL v2");
+-- 
+2.25.1
+